1. Specification: 4600*900*2050mm
2. The 4 main rods on the front side of the bed frame are made of 40*40*1.8mm special-shaped steel pipes, and the 4 main rods on the back side are made of 40*40*1.8mm square steel pipes;
3. The crosspieces around the bed frame are made of 40*40*1.8mm square steel pipes;
4. The bed frame crosspiece is made of 25*25*1.5mm thick square steel pipe, and the bed guardrail is made of 20*20*1.2mm thick square steel pipe, inlaid with 18mm thick double-faced melamine board, and the height of the guardrail is 30mm.
5. The bedside guardrail is made of round steel pipes with a diameter of 19*1.2mm.
6. The bed courtyard is made of rectangular steel pipe with 25*50*1.8mm thickness.
7. Add a soft-covered anti-collision strip on the outside under the bed board.
8. The bed board is assembled with 9 15mm thick fir slats, the gap between the slats is not more than 3mm, and the slats are required to be knotless and planed on both sides.
9. There are 6 support frames added between the cross rails around the bed frame, of which 4 are 45*50*840mm square wood files, and 2 are 25*25*1.5mm steel pipe files, which are respectively installed on 2.5mm steel plate welded U In the groove, the square log file requires no knots and planing.
10. The slats should be reinforced with wood screws not less than 40mm long on the 4 wooden stalls, two screws on each plank of the two-end wooden stalls.
11. The desktop board is made of 25mm thick double-faced melamine board, with solid wood edge banding, and brushed with high-quality environmentally friendly transparent paint.
12. The desk legs are made of 25*25*1.5mm square steel tubes.
13. Two-layer partitions are installed on the front of the bookshelf, made of 25mm thick double-faced melamine board, and the joint with the back board is reinforced with 2-3 screws. Three-layer partitions are installed on the side, made of 3mm thick steel plate, and the front and back are reinforced with screws to ensure that the furniture is stable and strong.
14. The drawer depth is 380mm, the side panels are made of 18mm thick double-faced melamine board, the floor is made of 5mm thick double-faced melamine board, the guide rail is made of stainless steel 3-section silent drawing rail, the handle is made of stainless steel round handle, and the lock is installed. Secret buckle.
15. The cabinet surface is made of 25mm high-quality environmentally friendly medium fiberboard, and the cabinet body is made of 18mm double-faced melamine board.
16. The cabinet is divided into two doors, the lower wardrobe is equipped with hanger hanging rods, which are made of round steel pipes with a diameter of 20mm, directly inlaid into the wooden boards on the left and right sides, and installed and formed at one time.
17. The cabinet door hinge adopts stainless steel long row hinges, and the cabinet door handle adopts stainless steel round handle, and it is equipped with exposed lock and concealed buckle.
18. The middle ladder uses a combination of steel and wood cabinet steps to link the two bed bodies, with a width of 600mm.
19. The first step is 100mm away from the ground, the cabinet height is 260mm, and the other levels are 360mm.
20. The steel frame is made of 25*25*1.5mm square steel pipe, and both sides of each step are reinforced by steel pipe diagonal welding.
21. The cabinet body is made of 18mm thick double-faced melamine board.
22. The tread surface is made of 3mm thick high-quality cold-rolled steel plate by one-step punching and forming, with pressure and non-slip stripes.
23. The cabinet door presses the circular built-in handle, and the door touches safely.
24. The furniture is yellow oak small embossed melamine double veneer panels, and the color of the steel parts is medium gray spray plastic, and the color is in line with the tender samples.
25. The steel frame used in the furniture is made of international steel. All steel parts must be subjected to strict pickling and phosphating treatment, using high-quality environmentally friendly plastic spray particles, electrostatic spray, high temperature curing, uniform spraying, smooth and smooth, and no spray coating is allowed to fall off. , Bubbling, depression, indentation and surface scratches, pitting, cracks, stretched feet, cutting edges, etc.
26. Welding parts of steel parts should be polished, clean and smooth, and bends should be full and smooth, and no accumulation of welding spots, exposed stubble, etc. are allowed.
27. The furniture handles, touches and other accessories are all stainless steel hardware, the guide rail is noiseless, and the handle is smooth.
28. The size of the workpiece is accurate, the consistency is good, and the flatness is high. The installation of various accessories should be tight, smooth, correct and firm. Cutting, drilling, chamfering and deburring, no chipping and loosening at the smooth joint.
29. The environmental protection of the board should reach the E1 level standard. It must be treated with waterproof edge sealing, no warping, no cracking, moisture and heat resistance, and the veneer and edge sealing parts are tight and smooth, without degumming or bubbling.
30. The unnamed parameters are based on bidding samples.
31. The chair has a plastic-steel structure, the chair surface and back are made of high-quality ASB plastic disposable compression molding, the chair frame is made of 70*30*20mm international square tube, the height of the frame is 370mm, the height of the chair is 440mm,
32. The color of the chair surface and back is red, and the color of the steel frame is dark gray